852
Bearbeitungen
LittlePrinter: Unterschied zwischen den Versionen
add some info about the interior of the printer itself
HKay (Diskussion | Beiträge) (Explain how to gain access to the bridge via SSH) |
HKay (Diskussion | Beiträge) (add some info about the interior of the printer itself) |
||
| (6 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt) | |||
|
= BERG =
== Little Printer ==▼
{| align="center" border="0"
|
[[Datei:Little_printer.jpeg|200px|thumb|right|The Little Printer by BERG]]
A few years ago a design company from London called "berg" introduced the Little Printer. The device basically is a small printer that prints various feeds provided by berg on a daily basis. Feeds like twitter, newspaper articles, trivia and sudoku. For that it uses regular receipt paper. ([https://www.youtube.com/watch?v=B_bytm9_P4w promo video])
The pricetag was 250 Euros.
In 2015 the company went into hibernation but kept the servers running for the rest of the year. Now, in January 2016 the devices are practically useless without the backend servers. I got mine dirt cheap on ebay. [[Benutzer:HKay|HKay]]
|-
|
[[Datei:Little_printer_bridge.jpeg|200px|thumb|right|The Little Printer bridge by BERG]]
The printer does not talk to the internet directly. That's what the extra box called "bridge" is for. It has a RJ45 connector for Ethernet and a ZigBee module.
|-
=== Hardware ===▼
|
[[Datei:Little_printer_bridge_v1.4_top.jpeg|200px|thumb|right|top of bridge v1.4 PCB]]
[[Datei:Little_printer_bridge_v1.4_bot.jpeg|200px|thumb|left|top of bridge v1.4 PCB]]
Right from the start the board offers several unpopulated pinheaders for JTAG and SERIAL. A quick check with the Oscilloscope reveals the pinout. And a logic analyser tells us the required baud settings. Baudrate: 115200 8N1 of course no hardware flow control. The voltage levels are 3.3 volts.
The board contains the following ICs
RAM: 48LC16M16A2 - 256 Mbit
=== Software ===▼
FLASH: 29F2G08ABAEA - 2Gb 16bit blocks
CPU: ATMEL AT91SAM9620
Ethernet tranceiver: KSZ8041NL
ZigBee Module: ETRX357
The rest is voltage regulation and logic
To connect to the board via a serial link I used the "SparkFun FTDI Basic Breakout". The RX,TX and ground pins are indicated in the picture above. Connect "RX"(receive pin) to the "TX"(transmit) pin on the FTDI board and the other way around. Also connect GND to GND. Make sure you have the 3.3V version as the 5V version would likely fry the board.
|}
Here is the boot chatter of the bridge.
The system is a AT91SAM9G20 at a clockspeed of 396 MHz running Linux with a kernel version of 2.6.36.4 in April of 2013
It has access to 32
The boot process finishes in a login prompt.
The obvious passwords default passwords don't work.
Now we just append init=/bin/sh to the end of the boot arguments. And continue booting.
<pre>
U-Boot> setenv bootargs console=ttyS0,115200 root=/dev/mtdblock6 mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,128k(env1),128k(env2),2M(linux),16M(config),-(root) rw rootfstype=jffs2 init=/bin/sh
U-Boot> run bootcmd▼
▲run bootcmd
</pre>
<pre>
#
</pre>
The printer converts the pre-formatted text and prints it onto regular receipt paper.
It also has basic software that enables it to print troubleshooting messages along with faces.
== Hardware ==
[[Datei:Little_printer_printer_v21.2_top.jpeg|200px|thumb|left|top of printer v21.2 PCB]]
[[Datei:Little_printer_printer_v21.2_bot.jpeg|200px|thumb|right|bottom of printer v21.2 PCB]]
[[Datei:Little_printer_printer.jpeg|200px|thumb|center|mechanical components of the printer]]
The long FFC connector X1(label hidden) at the top leads to the printer mechanics.
right below it is the stepper driver IC "BA6845FS".
All the other connectors on the topside are for debugging and therefore not populated.
The microcontroller is a Freescale "MC68HC908GP32". Pin 1 is marked by a little dot on the pcb.
| |||