LittlePrinter

Little Printer

A few years ago a design company from London called "berg" introduced the Little Printer. The device basically is a small printer that prints various feeds provided by berg on a daily basis. Feeds like twitter, newspaper articles, trivia and sudoku. For that it uses regular receipt paper. (promo video)

The pricetag was 250 Euros.

In 2015 the company went into hibernation but kept the servers running for the rest of the year. Now, in January 2016 the devices are practically useless without the backend servers. I got mine dirt cheap on ebay. HKay (Diskussion)

The Bridge

The printer does not talk to the internet directly. That's what the extra box called "bridge" is for. It has a RJ45 connector for Ethernet and a ZigBee module.

Hardware

TODO ADD PHOTOS OF THE BOARD

Right from the start the board offers several unpopulated pinheaders for JTAG and SERIAL. A quick check with the Oscilloscope reveals the pinout. And a logic analyser tells us the required baud settings. Baudrate: 115200 8N1 of course no hardware flow control. The voltage levels are 3.3 volts. The core of the board is a ATMEL AT91SAM9620.

Software

Here is the boot chatter of the bridge. The system is a AT91SAM9G20 at a clockspeed of 396 MHz running Linux with a kernel version of 2.6.36.4 in April of 2013 It has 32 Megs of RAM and 256 MiB of Flash (far more than required). The boot process finishes in a login prompt. The obvious passwords default passwords don't work. Datei:Little printer bridge boot log.txt

However the System boots with an unlocked uboot. The classic INIT=/bin/sh work around can be applied. When uboot asks you to press a button to stop the boot process for a uboot prompt we enter 'pri to get the boot parameters.

U-Boot> pri
...
bootargs=console=ttyS0,115200 root=/dev/mtdblock6 mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,128k(env1),128k(env2),2M(linux),16M(config),-(root) rw rootfstype=jffs2
...

Now we just append init=/bin/sh to the end of the boot arguments. And continue booting.

setenv bootargs console=ttyS0,115200 root=/dev/mtdblock6 mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,128k(env1),128k(env2),2M(linux),16M(config),-(root) rw rootfstype=jffs2 init=/bin/sh

run bootcmd

The boot ends in a root shell that we use to replace the current root password and reboot into the regular system.

/ # passwd
Changing password for root
New password: 
Bad password: too short
Retype password: 
Password for root changed by root
/ # sync

Once the default system is running you cannot make changes to the filesystem. That's why we have to remount it as writeable. Apparently the developer used dropbear to ssh into the bridge. It does not run on boot though. We have to add a init script.

# mount
rootfs on / type rootfs (rw)
/dev/root on / type jffs2 (ro,relatime)
proc on /proc type proc (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,gid=5,mode=620)
tmpfs on /dev/shm type tmpfs (rw,relatime,mode=777)
tmpfs on /tmp type tmpfs (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
/dev/mtdblock5 on /opt type jffs2 (rw,noatime)
# mount -o remount,rw /
#
# cd /etc/init.d
# cp S99bergcloud_bridge S99dropbear
# vi S99dropbear
# cat S99dropbear
#!/bin/sh

case "$1" in
    start|"")
        dropbear &
        ;;
    stop)
        killall dropbear
        ;;
    *)
        echo "Usage: S99dropbear {start|stop}" >&2
        exit 1
        ;;
esac
#
# ./S99dropbear

Now we can ssh into the device. There is still a ssh key from the original developer in the system. You might want to remove that file or replace it with your own key.

# cat ~/.ssh/authorized_keys
ssh-dss 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 nick@buildbot